Register | Log in
 
Electric-RC-Helicopter.com's Homepage
AlbumAlbum  | FAQ | Search | Memberlist
 

setup problem trex 450


Custom Search
Post new topic   Reply to topic
Electric Rc Helicopter Forum Index -> T-REX Goto page Previous  1, 2
View previous topic :: View next topic  
Author Message
Burgess
Extreme 3D
Extreme 3D


Joined: 27 Mar 2012
Posts: 1103
Location: Wales

PostPosted: Thu Dec 04, 2014 1:07 pm
PostPost subject:
Reply with quote

Bill use this link
look at fig 6

http://helihelp.rabbitsvc.com/SettingUpTheModel.aspx

The rudder connects to the gyro,
The gyro lead {black, red, white} connects to Channel 4
black (-) red (+) white (~ signal)
the gyro gain yellow wire (~ signal) connects to Channel 5

Ch 1 Aileron
Ch 2 Elevator
Ch 3 ESC
Ch 4 Gyro/Rudder control
Ch 5 Gyro gain
Ch 6 Pitch

Make sure that each lead is connected to the receive with the light coloured (~ signal) wire facing the receiver label.

When you move the rudder stick left, which way does the steering slider on the tail shaft move?

Can you upload a copy of your T6CONFIG file.




Burgess
Back to top
View user's profile Send private message
Burgess
Extreme 3D
Extreme 3D


Joined: 27 Mar 2012
Posts: 1103
Location: Wales

PostPosted: Fri Dec 05, 2014 10:09 am
PostPost subject:
Reply with quote

Bill, which direction has your helicopter been spinning round and round, clockwise, or anticlockwise?

Burgess
Back to top
View user's profile Send private message
Burgess
Extreme 3D
Extreme 3D


Joined: 27 Mar 2012
Posts: 1103
Location: Wales

PostPosted: Mon Dec 08, 2014 9:09 pm
PostPost subject:
Reply with quote

Bill,...buddy, you've asked for all the transmitter settings and also reported that the helicopter is spinning round and round; however, you omit to say the direction of spinning. This indicates that you have some settings programmed into your T6CONFIG file, such as Stick Mode and Throttle Curve.

Have you replaced the tail boom, if so the synchromesh belt may not be installed the correct way, and that would rotate the tail rotor the wrong way. Also the Rudder servo might not be in the correct position.

Please list your T6CONFIG settings

Some photos of the Rudder servo and the tail rotor would be helpful.

Which direction has your helicopter been spinning round and round, clockwise, or anticlockwise?

How much of the setting-up of your helicopter and transmitter have you managed to complete.


Have you got any response to:

Rudder stick movements?

Gyro Gain Left-hand knob VR(B)?

Flight Mode Left-hand switch(B) ?

Which direction does the tail rotor rotate?



Burgess
Back to top
View user's profile Send private message
Shaun96
Hopping Maniac
Hopping Maniac


Joined: 07 Jan 2015
Posts: 29
Location: San Fransisco

PostPosted: Fri Jan 16, 2015 2:44 pm
PostPost subject:
Reply with quote

Trim it properly. If the helicopter is spinning to the right (clockwise), you move the trim knob to the left. If the helicopter is spinning to the left (counter clockwise), you move the trim knob to the right.
Back to top
View user's profile Send private message
Display posts from previous:   
Electric Rc Helicopter Forum Index -> T-REX All times are GMT + 7 Hours
Post new topic   Reply to topic Goto page Previous  1, 2
Page 2 of 2
Jump to:  

 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum




Electric Rc Helicopter topic RSS feed 

SmartFeedSmartFeed




Electric-RC-Helicopter.com